# Working Principle of DC Generator and Basic Construction

Posted on

There are two types of generators, one is ac generator and other is DC generator. Each type of generator has working principle to start the machine. Working principle of dc generator is an important part of the machine to produce alternating induced voltage. Working principle of dc generator uses principle of Faraday’s law. A DC generator produces direct power. This generators produce electrical power, based on same fundamental principle of Faraday’s law of electromagnetic induction.

According to this law, when a conductor moves in a magnetic field it cuts magnetic lines of force, due to which an emf is induced in the conductor. The magnitude of this induced emf depends upon the rate of change of flux (magnetic line force) linkage with the conductor. This emf will cause a current to flow if the conductor circuit is closed.

# Working Principle of DC Generator and Basic Construction

Hence the most basic tow essential parts of a generator are:

1. A magnetic field
2. Conductors which move inside that magnetic field.

Now we will go through the working principle of DC generator. As the working principle of an AC generator is not in the scope of our discussion in this section.

## Single Loop DC Generator

In the figure above, a single loop of conductor of rectangular shape is placed between two opposite poles of magnet. Let’s us consider, the rectangular loop of the conductor is ABCD which rotates inside the magnetic field about its axis ab.

When the loop rotates from its vertical position to its horizontal position, it cuts the flux lines of the field. As during this movement two sides, i.e., AB and CD of the loop cut the flux lines there will be an emf induced in these both of the sides (AB and BC) of the loop.

As the loop gets closed there will be a current circulating through the loop. The direction of the current can be determined by Flemming’s right hand Rule.

This rule says that if you stretch thumb, index finger and middle finger of your right-hand perpendicular to each other, then thumbs indicates the direction of motion of the conductor, index finger indicates the direction of magnetic field, i.e., N – pole to S – pole, and middle finger indicates the direction of flow of current through the conductor.

Now if we apply this right-hand rule, we will see at this horizontal position of the loop, current will flow from point A to B and on the other side of the loop current will flow from point C to D.

Now if we allow the loop to move further, it will come again to its vertical position, but now the upper side of the loop will be CD, and lower side will be AB (just opposite of the previous vertical position).

At this position, the tangential motion of the sides of the loop is parallel to the flux lines of the field. Hence there will be no question of flux cutting, and consequently, there will be no current in the loop.

If the loop rotates further, it comes to again in a horizontal position. But now, said AB side of the loop comes in front of N pole, and CD comes in front of S pole, i.e., just opposite to the previous horizontal position as shown in the figure beside.

Here the tangential motion of the side of the loop is perpendicular to the flux lines; hence rate of flux cutting is maximum here, and according to Flemming’s right-hand Rule, at this position current flows from B to A and on another side from D to C.

Now if the loop is continued to rotate about its axis. Every time the side AB comes in front of S pole, the current flows from A to B. Again, when it comes in front of N pole, the current flows from B to A. Similarly, every time the side CD comes in front of S pole the current flows from C to D., When the side CD comes in front of N pole the current flows from D to C.

If we observe this phenomenon differently, we can conclude, that each side of the loop comes in front of N pole, the current will flow through that side in the same direction, i.e., downward to the reference plane.

Similarly, each side of the loop comes in front of S pole, the current through it flows in the same direction, i.e., upwards from the reference plane. From this, we will come to the topic of the principle of DC generator.

Now the loop is opened and connected it with a split ring as shown in the figure below. Split rings, made of a conducting cylinder, gets cut into two halves or segments insulated from each other. We connect the external load terminals with two carbon brushes which rest on these split slip ring segments.

### Basic Working Principle of DC Generator

We can see that in the first half of the revolution current always flows along ABLMCD, i.e., brush no 1 in contact with segment a. In the next half revolution, in the figure, the direction of the induced current in the coil is reversed.

But at the same time the position of the segments a and b are also reversed which results that brush no 1 comes in touch with the segment b. Hence, the current in the load resistance again flows from L to M. The waveform of the current through the load circuit is as shown in the figure. This current is unidirectional.

The above content is the basic working principle of DC generator, explained by single loop generator model. The positions of the brushes of DC generator are so that the change over of the segments a and b from one brush to other takes place when the plane of rotating coil is at a right angle to the plane of the lines of force. It is to become in that position, the induced emf in the coil is zero.

### Working Principle of DC Generator Conclusion

After going through the above portion of DC generator we can now establish working principle of DC generator. I hope you enjoy when reading this article, thank you.